Team Tube

Round Tubing Products
- Mechanical Tubing
- Fluid Power Products
- Pneumatic (Air) Cylinder Tubing
  - Nitro Tubing
  - Chrome Plated Tubing - ID
Round Bar Products

D.O.M. Steel Tubing

Test Reports available on request

ASTM A513 Type 5

Grade	Chemistry	%	Yield	Tensile	Elongation	Typical Hardness
			PSI	PSI	% in 2" section	Min
1020	Carbon	0.15-0.25	60,000	70,000	10	B-80
	MN	0.30-0.60
	P	0.040 Max
	S	0.050 Max
1026	Carbon	0.21-0.28	75,000	85,000	15	B-85
	MN	0.60-0.90
	P	0.040 Max
	S	0.050 Max
ST52.3	Carbon	0.13-.018	75,000	85,000	15	B-80
	MN	.012-.014
	P	0.025 max
	S	0.010 max

Diameter Tolerances

OD Inches	Wall:	OD Inches		ID Inches
Size Range	Percent of OD	Plus	Minus	Plus	Minus
Up to 0.499	All	0.004	0.000
0.500-1.699	All	0.005	0.000	0.000	0.005
1.700-2.099	All	0.006	0.000	0.000	0.006
2.100-2.499	All	0.007	0.000	0.000	0.007
2.500-2.899	All	0.008	0.000	0.000	0.008
2.900-3.299	All	0.009	0.000	0.000	0.009
3.300-3.699	All	0.001	0.000	0.000	0.001
3.700-4.099	All	0.011	0.000	0.000	0.011
4.100-4.499	All	0.012	0.000	0.000	0.012
4.500-4.899	All	0.013	0.000	0.000	0.013
4.900-5.299	All	0.014	0.000	0.000	0.014
5.300-5.549	All	0.015	0.000	0.000	0.015
5.550-5.999	Under 6"	0.001	0.001	0.001	0.001
	6" to 7 1/2"	0.009	0.009	0.009	0.009
6.000-6.499	Under 6"	0.013	0.013	0.013	0.013
	6 to 7 1/2"	0.001	0.001	0.001	0.001
6.500-6.999	Under 6	0.015	0.015	0.015	0.015
	6 to 7 1/2	0.012	0.012	0.012	0.012
7.000-7.499	Under 6	0.018	0.018	0.018	0.018
	6 to 7 1/2	0.013	0.013	0.013	0.013
7.500-7.999	Under 6	0.002	0.002	0.002	0.002
	6 to 7 1/2	0.015	0.015	0.015	0.015
8.000-8.499	Under 6	0.023	0.023	0.023	0.023
	6 to 7 1/2	0.016	0.016	0.016	0.016
8.500-8.999	Under 6	0.025	0.025	0.025	0.025
	6 to 7 1/2	0.017	0.017	0.017	0.017
9.000-9.499	Under 6	0.028	0.028	0.028	0.028
	6 to 7 1/2	0.019	0.019	0.019	0.019
9.500-9.999	Under 6	0.003	0.003	0.003	0.003
	6 to 7 1/2	0.002	0.002	0.002	0.002
10.000-10.999	Under 6	0.034	0.034	0.034	0.034
	6 to 7 1/2	0.022	0.022	0.022	0.022
11.000-11.999	Under 6	0.035	0.035	0.035	0.035
	6 to 7 1/2	0.025	0.025	0.025	0.025
12.000-12.999	Under 6	0.036	0.036	0.036	0.036
	6 to 7 1/2	0.027	0.027	0.027	0.027
13.000-13.999	Under 6	0.037	0.037	0.037	0.037
	6 to 7 1/2	0.029	0.029	0.029	0.029
14.000-15.000	Under 6	0.038	0.038	0.038	0.038
	6 to 7 1/2	0.003	0.003	0.003	0.003

Ovality shall be within the above tolerances except when the wall thickness is less than 3% of the OD.

In those cases the additional ovality shall be as follows, but the mean diameter shall be within the specified tolerance

Outside Diameter	Additional Ovality Tolerance	Outside Diameter	Additional Ovality Tolerance
Up to 2"	0.010"	7" - 8" incl.	0.040"
2" - 3" incl.	0.015"	8" - 9" incl.	0.045"
3" - 4" Incl.	0.020"	9"-10" incl.	0.050"
4" - 5" incl.	0.025"	10"-11" incl.	0.055"
5" - 6" incl.	0.030"	11"-12" incl.	0.060"
6" - 7" incl.	0.035"	12"-12.5"incl.	0.065"

Straightness Tolerance

.030” in any 3 ft. of length up to 7.500” OD
.060” in any 3 ft. of length over 7.500” OD

Wall Tolerances

Wall	Including	Over .875 to	Over 1.875 to	Over 3.750 to
Thickness,	.375 to	1.875 OD	3.750 OD	15.000 OD
Inches	.875 OD
0.028 & 0.035	0.002	0.002	0.002
	-0.002	-0.002	-0.002
0.049	0.002	0.002	0.002
	-0.002	-0.003	-0.003
0.065	0.002	0.002	0.002	0.004
	-0.002	-0.003	-0.003	-0.004
0.083	0.002	0.002	0.003	0.004
	-0.002	-0.003	-0.003	-0.005
0.095	0.002	0.002	0.003	0.004
	-0.002	-0.003	-0.003	-0.005
0.109	0.002	0.002	0.003	0.005
	-0.003	-0.004	-0.003	-0.005
0.120	0.003	0.002	0.003	0.005
	-0.003	-0.004	-0.003	-0.005
0.134		0.002	0.003	0.005
		-0.004	-0.003	-0.005
0.148		0.002	0.003	0.005
		-0.004	-0.003	-0.005
0.165		0.003	0.003	0.005
		-0.004	-0.004	-0.006
0.180		0.004	0.003	0.006
		-0.004	-0.005	-0.006
0.203		0.004	0.004	0.006
		-0.005	-0.005	-0.007
0.220		0.004	0.004	0.007
		-0.006	-0.006	-0.007
0.238		0.005	0.005	0.007
		-0.006	-0.006	-0.007
0.259		0.005	0.005	0.007
		-0.006	-0.006	-0.007
0.284		0.005	0.005	0.007
		-0.006	-0.006	-0.007
0.300		0.006	0.006	0.008
		-0.006	-0.006	-0.008
0.320		0.007	0.007	0.008
		-0.007	-0.007	-0.008
0.344		0.008	0.008	0.009
		-0.008	-0.008	-0.009
0.375			0.009	0.009
			-0.009	-0.009
0.400			0.01	0.01
			-0.01	-0.01
0.438			0.011	0.011
			-0.011	-0.011
0.480			0.012	0.012
			-0.012	-0.012
0.531			0.013	0.013
			-0.013	-0.013
0.563			0.013	0.013
			-0.013	-0.013
0.580			0.014	0.014
			-0.014	-0.014
0.600			0.015	0.015
			-0.015	-0.015
0.625			0.016	0.016
			-0.016	-0.016
0.650				0.017
				-0.017